Looking for:
John deere lt155 manual free download |
John Deere Manual | Service,and technical Manuals PDF.John deere lt lawn garden tractor service repair manual by kjsmfmmf - Issuu
John deere lt155 manual free download.JOHN DEERE
John deere lt155 manual free download -
Get medical attention immediately. Drink large amounts of water or milk. Then drink milk of magnesia, beaten eggs, or vegetable oil.
Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.
Operating equipment safely requires the full attention of the operator. Do not wear radio or music headphones while operating machine. Tie long hair behind your head. Do not wear a necktie, scarf, loose clothing, or necklace when you work near machine tools or moving parts. If these items were to get caught, severe injury could result.
Remove rings and other jewelry to prevent electrical shorts and entanglement in moving parts. Use tools appropriate to the work. Makeshift tools and procedures can create safety hazards. Use power tools only to loosen threaded parts and fasteners. For loosening and tightening hardware, use the correct size tools. Avoid bodily injury caused by slipping wrenches.
Use only service parts meeting John Deere specifications. Lower all equipment to the ground. Stop the engine and remove the key. Disconnect the battery ground strap. Illuminate your work area adequately but safely. Use a portable safety light for working inside or under the machine. Make sure the bulb is enclosed by a wire cage. The hot filament of an accidentally broken bulb can ignite spilled fuel or oil.
Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, open the doors and get outside air into the area. If you must work on a lifted machine or attachment, securely support the machine or attachment. Do not support the machine on cinder blocks, hollow tiles, or props that may crumble under continuous load.
Do not work under a machine that is supported solely by a jack. Follow recommended procedures in this manual. Lifting heavy components incorrectly can cause severe injury or machine damage. Follow recommended procedure for removal and installation of components in the manual. Clean work area and machine. Make sure you have all necessary tools to do your job. Have the right parts on hand. Read all instructions thoroughly; do not attempt shortcuts.
Gasoline engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Avoid potentially toxic fumes and dust. Hazardous fumes can be generated when paint is heated by welding, soldering, or using a torch. Do all work outside or in a well ventilated area.
Dispose of paint and solvent properly. Remove paint before welding or heating: If you sand or grind paint, avoid breathing the dust. Wear an approved respirator. If you use solvent or paint stripper, remove stripper with soap and water before welding. Remove solvent or paint stripper containers and other flammable material from area.
Allow fumes to disperse at least 15 minutes before welding or heating. Avoid breathing dust that may be generated when handling components containing asbestos fibers. Inhaled asbestos fibers may cause lung cancer.
Components in products that may contain asbestos fibers are brake pads, brake band and lining assemblies, clutch plates, and some gaskets. The asbestos used in these components is usually found in a resin or sealed in some way. Normal handling is not hazardous as long as airborne dust containing asbestos is not generated. Avoid creating dust. Never use compressed air for cleaning. Avoid brushing or grinding material containing asbestos. When servicing, wear an approved respirator.
A special vacuum cleaner is recommended to clean asbestos. If not available, apply a mist of oil or water on the material containing asbestos. Keep bystanders away from the area. Do not attempt to mount a tire unless you have the proper equipment and experience to perform the job. Always maintain the correct tire pressure. Do not inflate the tires above the recommended pressure. Never weld or heat a wheel and tire assembly.
The heat can cause an increase in air pressure resulting in a tire explosion. Welding can structurally weaken or deform the wheel. When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly.
Use a safety cage if available. Check wheels for low pressure, cuts, bubbles, damaged rims or missing lug bolts and nuts. Keep hands and feet away while machine is running. Shut off power to service, lubricate or remove mower blades, augers or PTO shafts. Direct exposure to hazardous chemicals can cause serious injury.
Potentially hazardous chemicals used with John Deere equipment include such items as lubricants, coolants, paints, and adhesives. A Material Safety Data Sheet MSDS provides specific details on chemical products: physical and health hazards, safety procedures, and emergency response techniques.
Check the MSDS before you start any job using a hazardous chemical. That way you will know exactly what the risks are and how to do the job safely. Then follow procedures and recommended equipment. Improperly disposing of waste can threaten the environment and ecology. Potentially harmful waste used with John Deere equipment include such items as oil, fuel, coolant, brake fluid, filters, and batteries.
Use leakproof containers when draining fluids. Do not use food or beverage containers that may mislead someone into drinking from them. Lay underneath the front of the mower, sliding your self right into a role in which you may get entry to the guidance equipment, that is the steel, fan-fashioned item on the decrease stop of the guidance shaft.
This will permit the equipment to fall far from the guidance shaft without disrupting the shaft elimination itself. Once the guidance equipment has been dismounted, go back from below the gadget and tilt the hood of the LT ahead over the front of the mower.
Locate the nut and bolt on the pinnacle of the guidance shaft, then do away with it with a ratchet and socket in addition to an open-stop wrench.
Push the bolt via the guidance shaft, then do away with the guidance wheel from the shaft. Skip to content Home » Download John Deere LT, LT, LT Lawn Tractors Service Repair Manual The John Deere LT become simplest created from to , however in spite of its noticeably quick manufacturing run and its vicinity as a decrease-stop version withinside the LT-Series, the ride-on garden mower is cherished and nevertheless, The LT is mild at more or less four hundred pounds, with a inch adjustable mower deck and a single-cylinder, thirteen horsepower Kohler engine.
Gripping the Shaft Once the guidance equipment has been dismounted, go back from below the gadget and tilt the hood of the LT ahead over the front of the mower.
No comments:
Post a Comment